Johnson 60 Hp Vro Manual
If it's similar to my 1998 Johnson 40 HP VRO. My manual is for 1995-1998 Evinrude and Johnson 2 stroke. Leaner mix on the oil,60-70:1 mix.dont do. Johnson Evinrude Outboard Motors - Online Shop/Service/Repair Manuals Download. 1965 Evinrude SportFour Heavy Duty 60 HP Outboards Service Manual, 4204. Johnson Evinrude 1971 To 1989 1 To 60hp Service Manual Pdf. Removal & 60 hp. Johnson / Evenrude 1973-1991 60-235Hp Repair Manual Johnson /. Jun 22, 2010 Just changed a 60 hp over from a vro pump to manual pump---its a 88 model---i took off vro pump--and primer - Answered by a verified Marine Mechanic.
Download mercury 60 hp service manual mercury 60 hp workshop manual pdf mercury idle adjustment turns 60 hp mercury mariner 60 hp manual mercury mariner 60 hp outboard manual mercury outboard 60 hp motor manual mercury outboard motor 4 stroke 60 hp lower unit repair mercury outboards1997 60 hp propeller mercury tracker 60 hp repair manual model u4 40 suzuki series 60 hp assembly instructions need water temp gauge for 1986 mercury 60 hp 3 cylinder o8 mercury 60 hp gear box workshop manual oil capacity for 1994 mariner 60 hp 3 cyl jet motor oil capacity for evinrude 60 hp two stroke.
Removing the VRO2 Fuel Pump 1. Position a shop rag beneath the fuel pump to catch any fuel that may leak from the lines.
Remove the black negative battery lead from the battery. Examine the VRO fuel pump and find the fuel outlet line to the carburetor on top of the pump. Cut the plastic zip tie that holds it in place, using a razor knife, and push the fuel line from the nipple on the pump. Compress the spring clamp on the pulse line, found at the center of the front of the pump. Slide the spring back onto the line that branches out to each of the three carburetors.
Remove the line from the pump. Push the branch lines from the fittings on the side of the top, middle and lower carburetor. Compress the clamp on the bottom line of the fuel pump -- the oil inlet line that leads from the tank by way of the prime bulb -- and push it backward on the fuel line. Push the line from the fitting on the pump. Feel around on the bottom-rear of the pump and find the oil supply line. The same type of spring clamp as the one used on the fuel inlet line keeps the oil supply line in place. Move the clamp back onto the line and remove the line from the pump.
Trace the pump wiring back to the point where it connects with the engine wiring harness. Disconnect the connector from the harness. Pull the wire from the wire loom. Locate the three pump-to-manifold bracket screws on the backside of the pump-mounting bracket.
Support the pump as you remove these screws with a flathead screwdriver, and lift the pump from the engine. Removing the Oil Reservoir 1. Feel around on the bottom-rear of the oil pump and find the oil supply line. The oil supply line is secured by the same type of spring clamp as the fuel inlet line.
Again, move the clamp back onto the line and remove the line from the oil pump. Remove the screws that hold the starboard-side lower engine cover -- the engine cover on the lower right side of the engine -- in place. Remove the wire for the three-pin wiring connector for the oil reservoir from the wire loom and disengage the it from the wiring harness. Remove the screw holding the top of the oil reservoir in place on the engine's top bracket.
Plug the hoses leading from the tank with a golf tee to prevent oil loss. Remove the screw securing the lower part of the reservoir to the powerhead and pull the reservoir away from the engine. Installing the New Pump 1. Place a bead of thread locker on the threads of the screws that will hold the new pump in position.
Position the gasket or O-ring that accompanies the pump onto the powerhead. Position the new fuel pump on the fuel pump mounting bracket and thread the three pump-to-manifold screws through the bracket and into the pump. Tighten the screws to 30 inch-pounds using a torque driver.
Connect the fuel outlet hose to the nipple at the top of the pump and secure in place with a zip tie. Compress the clamp on the fuel inlet line and slide the end of the line over the fitting on the bottom of the pump.
Slide the clamp over the fitting to hold the fuel line in place. Plug the fuel pump's three-pin connector into the wiring harness and fit the wire into the wire loom. Connect a fuel tank filled with a 50-to-1 mix of gasoline and outboard motor oil -- 2.88 ounces of oil per gallon of gas -- to the quick-connect on the priming bulb. Pump the priming bulb until it becomes firm and visually check for leaks in the system.
Replace the starboard-side lower engine cover. Kia Carnival Diesel 2016 Workshop Manual.
- by admin