Husky 6 5hp 60 Gal Air Compressor Manual
• 55 Answers SOURCE: For what it's worth Compressors are intended to be turned on and forgot (except for the noise). Just for grins lets assume you have the stapler and air hose.
Find great deals on eBay for husky 60 gallon air compressor. Ingersoll Rand 60 gallon Stationary Electric Air Compressor 5 HP 230/1/60. Husky Gal Air Compressor. When the shut-off (preset “cut-out”) pressure is reached, the compressor automatically shuts off.If the compressor is left in the AUTO position and air is depleted from the tank by use of a tire chuck, tool, etc., the compressor will restartautomatically at its preset “cut-in” pressure. Electric Air Compressor is rated 3.8 out of 5 by 90. Rated 2 out of 5 by Nolan from Bought new in 2014, failed today. Bought this unit new from HD in 2014, it was used DIY for 1 year then moved into my business for daily commercial use for the past 3 years. The compressor switch failed approximately 6 months ago and was replaced.
You need to hook up the air hose to the compressor there usually is one or to either couplers or npt fittings (threaded). Attach the hose to the compressor and using a quick coupler (prefered because it allows the gun to swivel) connect the gun to the hose. Turn on the compressor and wait for it to build up pressure and *******. At this point you will need to locate the regulator on the compressor.
It will be a knob next to one or two dial gages. Crank the regulator a quarter turn either direction while watching the gages.
It (one of them) moved either up or down. Now you know how the regulator works and your almost a contractor.
On to the stapler, load it and find a bit of scrap (what your working on would be best.) now shoot a staple into something and see if it goes in far enough or to far. Adjust the regulator to compensate. Do this until one of three things happens A you find the right staple depth B the compressor kicks on again, wait for it to turn off C you run out of nails, beer or intrest in the project. Once you have found the correct pressure for your needs. You may fire at will you don't need to wait for the compressor to cycle while running the stapler just during set up.
Now your a contractor go have a beer. Just a last tip if you find you don't have the correct couplers home depot, harbor freight or amazon (online) are great sources for parts. Good luck and mind your fingers Rob Posted on Dec 10, 2008. • 82 Answers SOURCE: Depends on what plan it was made in. If you have the glass type sight. Only to the max you can see (top of site), then run it for a few mins, let it sit for a few more mins then add more if the level is near the bottom of the sight glass.
If it's the dipstick model that pushed in, there will be an upper and a lower level mark (holes, or checkered section) Keep it between the top and bottom marks. Finally if it's the older screw-in type, remove the dipstick and wipe it. Set it back in BUT don't screw it in. 2004 Hunter 36 Sailboat Manual. Keep within the range on the dipstick from that position. Isuzu Trooper 4jb Manual. Then of course screw it back in/ Good luck Posted on May 08, 2009.
• 1 Answer SOURCE: i have the same piece of junk, iv rebuilt it 3 times in the past 5 years always a piston rod snapped and then it was running on only one. They are built like ****. Anyhow I finely got smart and bought a cast iron pump thats not only quieter but puts out twice the volume of air in half the time.
It took some work but it was well worth it costing under 200.00. The rebuild kit from sears will cost over 100 and it wont last. The one from sears is a direct drive pump and you will be told no one makes a direct bolt on but all it takes is cutting the aluminum housing away from the motor and welding a pin or bolt to the end of the shaft and putting a pully on it, you will also have to turn the motor to the side but let me tell you this was the best move i ever made. You can pick I bought my new pump from a place called heavy dudy air in ga. 877-447-2485 Posted on Jan 18, 2010.
Master Tool Repair is an authorized re-seller of all products listed throughout our site. Master Tool Repair, is not affiliated with, or sponsored or endorsed by, any of the original equipment manufacturers whose names, logos, and/or trademarks are displayed on this page. Master Tool Repair provides replacement parts that are OEM or compatible with the original products of these manufacturers. Master Tool Repair sells replacement parts for Husky and Workforce products that we obtain from third parties, and not from the owner of the Husky and Workforce product lines. Master Tool Repair is not affiliated with, or sponsored or endorsed by, the Husky or Workforce product lines or their owner.
- by admin